General Updates


11695795 1463684873952951 1578145155291573139 n

We recently got the following message from Aptyx Designs, currently the #3 seed and a semi-finalist in this season's BattleBots.

Want to see how our frame was built? We designed all of our aluminum unibody frame to be waterjet cut by Big Blue Saw! The frame is all 1/4", 3/8", and 1/2" 6061 aluminum plate. By designing the parts with interlocking puzzle tabs, there is a strong mechanical joint even before welding!


This method allows for super fast construction, accurate jigging for welding, and a strong mechanical joint by having the zig-zag weld area, and lots of filets for welding.


If you design parts, you can upload them to Big Blue Saw and get instant quotes, including the material costs, and see how your design affects the pricing! No need for sending out for quotes and waiting, they are super easy to work with.


After all of or parts were waterjet cut, we were able to do minimum fit up work, jig everything together, and get Applied Welding in Mountain View to weld everything up for us! Welding thick aluminum requires a very experienced shop to ensure proper penetration and minimal warping. Eddie Irlanda is our man for welding everything!

To learn more about designing assemblies for waterjet cutting, read our articles on construction techniques for use with waterjet cut parts.


10253980 1463684923952946 7328895289249109459 n


10891992 1463684890619616 5373878623074514166 n



11745832 1463684907286281 7567342577266831783 n



11703360 1463684940619611 300330831975966385 n



11703190 1463684960619609 5574470623640795768 n

If you need custom parts for your robot, read more about how Big Blue Saw can turn  your ideas into real parts made of aluminum, steel, and more.





thumb piano 800

When it comes to custom parts for musical instruments, Big Blue Saw is the top choice for the instrument makers and musicians in the know. Over the years, we've made specialized guitar capos, sitar bridges, replacement accordion parts, and much more.

I've never seen an entire musical instrument using waterjet cut parts, though, so I set out to create one. After considering several possibilities, I decided to build a simple thumb piano. A thumb piano consists of a set of tine each tuned to a different note. When plucked, the sound of each tine resonates in a chamber to amplify the sound.

I started by using the free xylophone bar length calculator from Windworld. I input the longest bar length of 4 inches, and the calculator spit out the lengths of all the bars such that they would form an octave plus one higher note. The shortest bar was 2.83 inches accoding to the calculator. From there it was easy to design a "comb" with the various tines.


Next, I needed a resonating chamber. The best way to do this with waterjet cut parts is via the stacking technique, described in its own article. I designed a plain flat piece for the bottom, pieces with cavities for the middle layers, and a top with a resonating hole for the sound. I added holes so that I could bolt all of the pieces together, including the comb. Finally, I added two more small spacer pieces so that the comb could rest slightly elevated from the top of the resonator.


With this design, I could use just about any material and thickness that would be stiff enough for the tines to vibrate. I chose 1/8" thick aluminum 6061 alloy as it's relatively inexpensive and this was just a prototype instrument, after all.

After the parts were waterjet cut, I bolted them together using #10-24 machine screws.

thumb piano2 800

Now it was time to play. How does it sound? Check out the video below.

OK, it's a little out of tune. This is partly due to the calculator I used being designed for free floating xylophone keys, not tines which are all connected on one end. The higher notes sound more musical than the lower notes, so if I had to do it again, I'd start with the longest tine being around 3 inches. I would also consider using more and thicker bolts to hold the case together, as I noticed sublte rattling of the layers when the notes are struck. Plucking one note can cause the others to ring a little bit, so I would change the design to isolate the notes a little better, perhaps by using multiple combs. Finally, brass might make a better choice than aluminum for the material, as it's a more "musical" metal.

If you've got any more ideas for improving this thumb piano, let me know in the comments section or by e-mailing


This weekend, don't miss the second appearance of Bite Force from Aptyx Designs, sponsored by Big Blue Saw.

Tune in to BattleBots this coming Sunday, July 12 at 9pm on ABC Television Network when Bite Force faces off against HyperShock in the round of 16!

google plus reviews.2015-06-21.png

The reviews prove it: our customers love us. We've got a 5 star rating on Big Blue Saw's Google Plus page.

Check out more Big Blue Saw reviews and testimonials.


Big Blue Saw is proud to announce we're sponsoring a robot created by Paul Ventimiglia and his new team, Aptyx Designs, for the BattleBots robot fighting competition.

As a sponsor, Big Blue Saw waterjet cut the robot's  aluminum frame based on the CAD drawings provided to us by Aptyx Designs.

The 2015 BattleBots competition will be televised starting on June 21. Until then everything remains TOP SECRET! We cannot even reveal the name of Paul's robot! We will say that we think it's pretty amazing

But here is a EXCLUSIVE sneak peek at the design of some of the waterjet cut 3/8" thick aluminum parts you'll see in this new powerful fighting robot:

battlebots robot

How do those pieces fit together to make a robot? If you've read our article on tab and slot construction, you should have a pretty good idea. Or you can read more articles about how to design parts for waterjet cutting.